TX-18301 TFU Shadow Guard Kit by WTF build

As seen in the video game "The Force Unleashed". Now an approved costume!

Post Reply
changbanger
Posts: 13
Joined: Sat Jun 27, 2020 7:02 am
TKID: 18301

TX-18301 TFU Shadow Guard Kit by WTF build

Post by changbanger »

Hey all,
TX-18301 here from the Empire City Garrison.
I'm looking to log my build here of my TFU Shadow Guard kit by WTF. This can be a reference for other builders or just a build log for myself to track my progress, efforts and lessons learned. I welcome all of you to please actively and constructively critique my progress, offer suggestions and comments. I'm hoping this might be helpful to some future shadow brethren. Thank you.

Kit: Walt's Trooper Factory http://waltstrooperfactory.com/

Tools Used
Gerber Box Cutter: https://www.amazon.com/Gerber-Superknif ... 987&sr=8-7
Epoxy Glue: DeVCon https://www.amazon.com/gp/product/B003N ... UTF8&psc=1
Sandpaper: Dollar Tree
Nylon Strapping: https://www.amazon.com/gp/product/B01KT ... UTF8&psc=1
Elastic Strapping: https://www.amazon.com/inch-Elastic-Sew ... 387&sr=8-5
Snaps: https://www.amazon.com/gp/product/B003A ... UTF8&psc=1
Glue for Snaps: E6000 https://www.amazon.com/E6000-231020-Adh ... 625&sr=8-5
Snap Setter: https://www.amazon.com/gp/product/B005B ... UTF8&psc=1
Dremel: https://www.amazon.com/Dremel-4000-2-Pe ... 5149aa9081
Lexan Scissors: https://www.amazon.com/Du-Bro-Products- ... 579&sr=8-5
Masking Tape
Earths Rare Magnets

Accessories:
Kama: TBD
Jumpsuit: https://www.amazon.com/gp/product/B007E ... UTF8&psc=1
Gloves, boots, Belt: https://www.imperialboots.com/
Cape and Saberpike: TBD

Day 1:
I started working from less intimidating parts first so I rough cut and dremel sanded the following parts in that order: Spats, Shoulder bells, Chest, Back, Shins.
Some of the pieces had lines or creases to guide my cutting but most did not so for the most part I referenced the 501st CRL and a few helpful 501st guardian angels who have sent me pics of their armor and offered advice. For all of the rough cuts I left a large return edge then when sanding it down with the dremel I sanded it a little at time then tried it on then sanded some more. I expect to leave at least 1/8th of of inch of return on all of the parts to give a sense of armor thickness.

Walt's armor is nicely made, thicker than Anovos armor. There are some areas with wrinkles but rarely in an area that shows most are below the cut lines. His armor is pretty close to trimmed as well I found that I probably could have just dremelled my way through most it with minimal cutting.

For the next day I expect to install the strapping onto the armor I trimmed and probably sand more as needed for comfort. I still have to work on the helmet and vanbraces. After speaking with Walt and a few other folks I am going to leave it uncut and plastic well both the helmet parts and the van braces together then sand them down and paint but I'll need to build up some courage before I do. Until then the plastic glue and jumpsuit are on their way to me.
Attachments
20200715_122555.jpg
20200715_122555.jpg (730.58 KiB) Viewed 4771 times
20200715_113702.jpg
20200715_113702.jpg (743.12 KiB) Viewed 4771 times
20200715_113659.jpg
20200715_113659.jpg (754.66 KiB) Viewed 4771 times
Last edited by changbanger on Fri Jul 17, 2020 9:53 pm, edited 1 time in total.

Allan1313
Posts: 149
Joined: Sun Jul 03, 2016 2:43 am
TKID: 97491

Re: TX-18301 TFU Shadow Guard Kit by WTF build

Post by Allan1313 »

Welcome Eddie! Always good to see another ECG member.

Sent from my Pixel 2 XL using Tapatalk

Image
Red TFU Guard
Empire City Garrison

changbanger
Posts: 13
Joined: Sat Jun 27, 2020 7:02 am
TKID: 18301

Re: TX-18301 TFU Shadow Guard Kit by WTF build

Post by changbanger »

Thanks brother good to be here

changbanger
Posts: 13
Joined: Sat Jun 27, 2020 7:02 am
TKID: 18301

Re: TX-18301 TFU Shadow Guard Kit by WTF build

Post by changbanger »

Day 2:
I was able to get the strapping done. Trimmed out the helmet and vanbraces and sanded down the edges. Tomorrow I plan on gluing them all together. Wish me luck

Dansaliv
Posts: 2
Joined: Mon May 17, 2021 6:55 pm
TKID: 54197

Re: TX-18301 TFU Shadow Guard Kit by WTF build

Post by Dansaliv »

Hi Changbanger, I bought the jumpsuit to you recommended but now I see it has a lot of pockets. Did you remove any of the pockets for your approval? Thanks in advance.

changbanger
Posts: 13
Joined: Sat Jun 27, 2020 7:02 am
TKID: 18301

Re: TX-18301 TFU Shadow Guard Kit by WTF build

Post by changbanger »

I actually havent even submitted for approval yet. I took some time off of the build and am just getting around to working on it again. I'm still covering the seams up and sanding and priming and painting the armor. I expect to leave the pockes as they will be pretty hidden.

manitobamando
Posts: 2
Joined: Tue Apr 23, 2019 4:55 pm
TKID: 0

Re: TX-18301 TFU Shadow Guard Kit by WTF build

Post by manitobamando »

I am also just getting back into my build after WAY too long a break. Following this. :shadow:

changbanger
Posts: 13
Joined: Sat Jun 27, 2020 7:02 am
TKID: 18301

Re: TX-18301 TFU Shadow Guard Kit by WTF build

Post by changbanger »

Starting up again now still filling and priming and sanding seams

katkienzle
Posts: 3
Joined: Mon Oct 25, 2021 8:17 pm
TKID: 72261

Re: TX-18301 TFU Shadow Guard Kit by WTF build

Post by katkienzle »

Hello,

I know I am a little late to the party. I jumped in the deep end and bought the kit not thinking that soft parts may be very difficult to find quality work that would be approved. Did you have any luck finding the robes by chance? Or does anyone out there have any information on where to find soft parts for the shadow guard kit. My kit is also WTF and I am just beginning the task of cutting and sanding. We have an armor party coming up in a few weeks I hope to have the parts all sanded and ready to start assembly. ANY and ALL help is greatly appreciated.

ID72261
Kathy

Post Reply